J71 Original was longer than Information Code or is printed on the Transaction Journal instead. Information Code is printed on the Transaction Journal instead. J92 The Original was pulled out when feeding an original. A The ADF does not go off after the predetermined time. J94 Unexpected Jam timing i. Original is too short, etc. Mechanical Error Codes E Code. Laser Unit is defective. LVPS connectors is disconnected.
SC PCB is defective. Drive Mechanism is defective. Main Motor connector is disconnected. Main Motor is defective. Fuser Thermistor is dirty. Thermistor position is incorrect. Fuser temperature is low. Thermistor is defective. Fuser Lamp connector is disconnected.
Fuser Thermostat is defective. Fuser Lamp is defective. E4- 10 Exhaust Fan Motor Rotation 1. Exhaust Fan connector is disconnected. Fuser Unit Side 2. Exhaust Fan is defective.
Abnormal 2. E5- 19 Scanner Line Synchronization 1. Sort Memory defective. SC PCB connector is disconnected. SC PCB defective. Incorrect Hardware Key is installed. Hardware Key is defective. Out of Toner. Low Toner Sensor is disconnected. Low Toner Sensor is defective. Note: These error codes will appear only when the optional accessories are installed. Information Code Table For Facsimile. Leading edge of the recording Recording paper jam. Exit Sensor.
Recording paper has not completely passed the Paper Exit Sensor. No recording paper or paper is not set COPY properly. No Paper Sensor is defective. Paper Tray. COPY than 2 meter or Defective Read Point Sensor. No toner. Toner is getting low. Toner Cartridge has not been installed. Defective Toner Cartridge Sensor. Cover is not firmly closed. Connectors are not firmly connected. Door is not firmly closed. START button was pushed. Telephone line was disconnected while dialing. Receiver is defective.
Possible incompatibility or incorrect Password. Document to be transmitted is not placed at the transmitter. Modem, etc. Password RCV-Password mismatched. Last 4 digits of TSI does not match with Comm.
Selective RCV incomplete. No paper, paper after it transmitted post message, jamming, etc. Password does not match between transmitter and receiver. Transmitter is defective. No original, document jam, etc.
There are response to post message. There are response to PRI-Q from excessive errors in received data transmitter. Non-facsimile communication Transmitter is defective. Wrong number is dialed. RCV transmitted. Line quality is poor.
EOL is damaged received message data. RCV or continued ON for long time. RCV V. Line is disconnected. Polling station. No polling original is set. Built- Operator removed the original from the in dialer engaged ADF after dialing was completed. Original was not set properly in the ADF. No dial tone detected. Sensor dial tone Polling is not detected. Note: U. An unexpected LAN problem occurred.
Incorrect IP Address is set. No email application is activated on the Mail Server. Mail Server is defective. The resolution. POP Server is down. Incorrect User Name or Password is set. Address, etc. Incorrect DNS Server address is set. Internet Fax. Contact the Network Administrator. Email from a PC. Polled station are not properly set.
LAN Memory file access error. Changing some of these parameters may cause the unit to be no longer compliant or become inoperable. Service Mode Procedure 1. F5 Function Parameters Various function settings selected by code numbers can be changed. F6 Adjust Parameters Various function settings selected by code numbers can be adjusted. F Auto contrast adj. F Dept. F Oper.
F Paper out Indicator On F F Reduce N in 1 space No. F Photo Image Density 0 F F Orig. F Trail Edge Read Tim. F Trail Edge Prt Tim. F Side Adjust Bypass 0 F F Side Adjust Tray 1 0 F F Side Adjust Tray 2 0 F F Lead Edge Read Tim. F Side Edge Read Adj. F Stamp Position Adj. Set the machine to service mode and press "4" key on the Keypad.
F4 Mode Check Output No. Set the machine to Service Mode and press "5" key on the Keypad. F5 Mode No. Set the machine to Service Mode and press "6" key on the Keypad. The Factory Setting is different in each model. F6 Mode Setting No. Adjustment of trail edge void. Printer Density Adjustment for Printer. Adjustment of verification stamp position.
F7 Mode: Electronic Counter. Set the machine to Service Mode and press "7" key on the Keypad. F7 Mode No. Set the machine to Service Mode and press "8" key on the Keypad. F8 Mode No. Item Remarks Not Used 06 Error Log View a Each time the arrow key is pressed, the machine errors or paper jam codes stored in memory are displayed, beginning with the oldest code.
Note: Only the 30 most recent codes are displayed. Print out the Test Pattern. F9 Mode: Unit Maintenance. Set the machine to Service Mode and press "9" key on the Keypad. Mode 2 Absolute Address Setting of Real address. Clears with Shipment Set. Fax Service Mode Procedure. To enter the Fax Service Mode a. FAX Service Mode Table The following service modes are provided to assist you in setting operational functions of the unit and determining the condition of the unit.
Function Parameter Table No. See Note 1 Hub : When the polling command is initiated, the machine will continuously poll originals from the remote stations until it is interrupted by pressing "STOP".
When bps communicating with Super G3 V. Used when Echo Suppression is disabled. Selects the pause interval from 1 sec. Only INC. ON : Always prints. Selects the line disconnect condition during lines reception. If the number of line errors exceed this lines setting, the unit will disconnect the line.
Available if No. Up to 40 characters Programmed in the User Parameters. Note: After enabling this feature, aside from entering the text in the User Parameters, it also has to be activated in each Auto Dial Number before it will take effect. It does not work for Direct Dialed Numbers. Depending on the setting of the User Parameter Facsimile "No. Note: If a regular polled file is stored in memory, the Program Key for Continuous Polling will not be accepted.
Print the Function Parameter List to confirm the default settings. Interval:[ms] ms Conti. Page Memory Test A test pattern prints out for checking the page memory and printer mechanism using the following procedure. Printer Report All printer errors are logged on the Printer Report which can be printed by the following procedure.
MMM-dd-yyyy J00 Refer to the Supply list. Fax Service Mode 4 Modem Test 4. Binary Signal This Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure. Tonal Signal This Service Mode is used to check the tonal signal output.
The DTMF signal can be generated using the following procedure. Binary Signal V. Note: This operation should be performed when the unit is first installed. Overview This feature enables the Authorized Servicing Dealers to manage and improve the machine maintenance to their customers by alerting them of equipment problems. The function overview is as follows: 1. The printer report can be manually printed when required. When printer errors occurs, the unit can automatically transmit the Service Alert Report to the pre- registered telephone number or email address.
When the unit detects Low Toner or PM counter reached the maintenance timing, it can automatically transmit the Maintenance Alert Report to the pre-registered telephone number or email address.
See Sect. Service Alert Report When the unit detects an Emergency Printer Error, the unit will immediately transmit the Service Alert Report to the pre-registered telephone number or email address. However, the unit will not transmit the Service Alert Report if it finds the same error within the same date in the error log. Maintenance Alert Report When the unit detects Low Toner, the unit can automatically transmit the Maintenance Alert Report to the pre-registered telephone number or email address.
Refer to the Error Code Table. Call Counter Report When the printer counter reaches the pre-set number, the unit can automatically transmit the Call Counter Report to the pre-registered telephone number or email address. E13 O Out of Toner. U13 O M Low Toner. Service Mode 9 System Maintenance 4. Overview This Service Mode is used to maintain the machine.
Use the following procedure for System Maintenance. The display changes to the Fax Mode. After the transmission, the machine returns to the Stand-by Mode. Note: If there is NO File in the machine, this operation will not function. System Maintenance Table No. Panasonic Document Imaging Company and other Panasonic Sales Companies reserve the right to change any information enclosed herein without prior notification.
This includes, but is not limited to, parts pricing, availability, and text 2. Electrical parts supplied may include previously used components. Important Safety Notice Components identified by a mark, have special characteristics important for safety. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time.
The retention period of availability is dependant on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available. However, the individual contents of the assembly will be available for the standard period. Supplier "OAPD" is the supplier code For Screw identification and Part Number, please refer to the last section of this chapter.
Safety Ref. X8 X8. Y14 H7 Y3 8 Y14 Fig. Y3 6. Cover Assembly. Y13 2 S6 3 19 Y14 T9 T9 5 T8 T8 T8 7. Right Side Parts. Y3 3 Y3 T9 4. Motor and Drive Gear Unit. Left Side Parts. Y3 5. T9 7 Y3 U3. Y3 4 Y14 Y Y3 Y3. Rear and Upper Parts. W4 W4 3 U9 T9 Fuser Unit. Bottom Parts. P3 T9 1. U1 2 U1 Mechanical Base. Y3 2 Y3. U8 6 T9 T9. U8 7 U1. U1 U1. Paper Tray 2nd Paper Feed Module. U8 PC Boards. CN CN CN CN 7.
PNL2 5. CN 6. PNL4 7. Packing and Accessories. U1 1 , Hardware Identification Template. Open navigation menu. Close suggestions Search Search. User Settings. Skip carousel.
Carousel Previous. Carousel Next. What is Scribd? Explore Ebooks. Bestsellers Editors' Picks All Ebooks. Explore Audiobooks. Bestsellers Editors' Picks All audiobooks. Explore Magazines. Editors' Picks All magazines. Explore Podcasts All podcasts. Difficulty Beginner Intermediate Advanced. Explore Documents. Panasonic UF Service Handbook. Uploaded by pxs Did you find this document useful?
Is this content inappropriate? Report this Document. Flag for inappropriate content. Download now. Related titles. Carousel Previous Carousel Next.
Jump to Page. Search inside document. Note: Refer to the Quick Guide when installing the machine. Station Name 10 15 Characters 12 Ver. Address Numbers 20 Scanner 19 Ver. Required Tools No. Preventive Maintenance Method Important No. Firmware Emergency Recovery 2. RCV 47 Ver. Fax Service Mode Procedure 1. Note 2: Function Parameter No. Refer to the Supply list 89 Ver. ADF Safety Ref. Cover Assembly Safety Ref. Right Side Parts Safety Ref. Left Side Parts Safety Ref. Rear and Upper Parts Safety Ref.
Fuser Unit Safety Ref. Bottom Parts Safety Ref. Mechanical Base Safety Ref. Paper Tray Safety Ref. PC Boards Safety Ref. Packing and Accessories Safety Ref. Hardware Identification Template Ref.
Part No. Hendro Nugroho. Henry Raman. Ayman Soliman. Armando M. Joe Chai. Dragos Stefan. Registration of Domain Name ID Timeout Setting Auto Reset Time Setting Lockout Setting Authentication Method Setting Job Tracking Setting RightFax Server Setting Administrator Login Description of Job Tracking Notice Description General.
The User Authentication works for the devices under the management of the Windows Server. As a result, users must be authenticated before they can use the functions of the machine copying, faxing, scanning, and printing. The supported authentication protocol is NTLM v2. Users login to the Panasonic machine using their Windows account user name and password.
The system administrator can manage user accounts by using the Windows Server. User authentication can be set independently for each functions copying, faxing, scanning, and printing. In Windows , this protocol can also be used to maintain. When using User Authentication, it is also possible to use the Job Tracking function as well.
The Email to the administrator includes the name of the machine user, destination, and communication time, together with the image of the document that was sent or received. The following jobs are only tracked with this function. Reception from Internet Fax or PC. When the Job Tracking function is enabled, the following functions are not available. All the fax logs can be easily be managed by a single server. When using with the User Authentication function, it will increase the security by controlling the usage and identifying the users.
POP receive content of fax. When using User Authentications. The fax document to be sent is passed to the RightFax server via Email. A user who sends a fax from a Panasonic machine can receive a send confirmation report on the PC from the RightFax server.
When the RightFax function is enabled, the following functions are not available. Requires RightFax Ver. User for Machine Using. Users must enter login name and the password before using the devices which User Authentication function is enabled. Authentication is performed using the user's Windows account.
A login prompt appears if user authentication is enabled. If user authentication is disabled for the fax function, the control panel displays the standby message and the login prompt only appears when a function that requires authentication is selected. Enter your user name, and press SET. Up to 40 characters. Enter your password, and press SET. Up to 40 characters The password is case-sensitive. Press or to select the domain, and then press SET. Ex: PANA This completes authentication.
After completing authentication, you can use the selected functions copying, faxing, scanning, or printing. One of the following messages appears if authentication fails. Authentication is cancelled if no operation is performed on the machine within a certain time after authentication completes. In this case, you need to perform user authentication again before you can use the machine. See "ID Timeout Setting" on page 17 for details. The system administrator can specify whether authentication is required independently for each machine function copying, faxing, scanning, and printing.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password?
Enter your email address and check your inbox.
0コメント